Water spraying out of a wall or raining through a light fixture is not a wait-until-morning problem. Shut the main, then call Water Heater Repairer and a live dispatcher will route you to an independent, licensed and insured plumber near you, plus a water damage contractor if the mess calls for one.
Every burst line creates two problems, the broken pipe itself and the soaked structure around it. We line up both trades so you are not making five calls while water keeps moving.
Repairs to supply lines fall under plumbing code, which is why we route only to licensed, insured independent plumbers. Feel free to ask for their license at the door and verify it yourself.
A spraying line inside a finished wall gets priority over a slow drip under a sink. Response is typically fast, though a hard freeze can stretch every schedule in town.
You get a written, flat-rate quote for the repair and any wall access before anything gets cut. You know the number before the first tool comes out.
Many contractors in the network carry acoustic leak detectors and thermal imaging cameras. That narrows the break down to inches instead of tearing out a whole wall to hunt for it.
Split copper, popped PEX fittings, brittle CPVC, and leaks under the slab are all daily calls here. Describe the pipe and where it is, and we connect you with a plumber who handles that exact material all the time.
When water has already soaked drywall, insulation, or subfloor, fixing the pipe is only half the job. A drying contractor with moisture meters, air movers, and dehumidifiers can be sent so the cavity dries out before the wall is patched. Closing a wet wall is how small leaks turn into mold calls months later.
Pipe material, location, and the reason it broke decide which repair makes sense.
Pipes running through outside walls, vented crawlspaces, and attics are the first to freeze. The ice pushes pressure toward a closed fixture until the pipe splits, and the leak usually shows up once it thaws.
Thin-wall Type M copper splits and pins faster than heavier Type L. The fix is cutting back to clean pipe and joining it with a sweated or press fitting.
PEX rarely splits, but crimp and expansion fittings can blow off when water freezes inside them. Aging CPVC gets glass-brittle, so a cracked elbow often means nearby joints are close to failing too.
A warm patch on tile or a water meter still moving with everything off usually means the leak is under the slab. Acoustic detection and thermal imaging pin it down, then you weigh a spot repair against a reroute through walls or attic.
Old galvanized pipe corrodes from inside out, and the threads are usually where it gives up. Fixing one joint on a corroded system tends to stress the next weakest point.
Braided supply lines under sinks and toilets burst without warning, and they run at full house pressure. A relief valve on the water heater that drips or dumps water needs a look too.
Four steps, and you talk to a person at every one of them.
We walk you through finding the main shutoff and killing power to any wet circuits. Then we ask what the pipe is made of, where it runs, and whether a ceiling is bulging.
We route the job to a nearby licensed plumber who carries stock for copper, PEX, and CPVC repairs. If water spread past the leak area, a water damage contractor can be scheduled right behind them.
The pro locates the split, looks over the rest of the line, and notes any pinholes or brittle fittings nearby. A written, flat-rate quote comes before any drywall is cut.
After the repair, the system is repressurized and tested, and joints are checked dry before the wall goes back. Ask about the contractor's own written workmanship warranty before they leave.
A push-to-connect coupling can stop a spraying line in minutes, which makes it a solid emergency patch. Most plumbers treat them as temporary inside a closed wall, and come back to sweat or press a permanent joint once things dry out.
Close the main valve, then call and we will route a local licensed plumber to you.
The line in the laundry room's outside wall froze and split the first really cold night. I found the main because the dispatcher stayed on the phone with me, and the plumber had the split copper cut out and replaced within a couple hours. He also showed me the Type M pipe and explained why it went first.
The bill jumped and part of the hall floor was warm to bare feet. The plumber used a listening device and a thermal camera and found the slab leak in about twenty minutes. We got two written prices, spot repair or reroute, and he explained both without pushing.
A toilet supply hose upstairs burst and the dining room ceiling started dripping. One call got me a plumber for the line and a separate drying contractor for the ceiling and carpet. Having both lined up from one call saved me a long night of searching.
I manage a small rental, and a tenant called about a CPVC elbow that cracked under the kitchen sink. After the repair he showed me how brittle the other joints were, and two of them snapped in his hand. He quoted a full repipe of that wall in writing and did not pressure me to do it that day.
Shut off the main water valve, then switch off breakers for any circuits near the water. Open a lower faucet to drain the lines, move valuables, and call so a plumber can head your way.
Turn on the connected faucet and apply gentle heat with a hair dryer or a space heater nearby. Never use a torch or open flame, since it can scorch framing or flash steam inside the pipe.
They are code-approved in many places, yet a lot of plumbers prefer them only where they stay accessible. Have the plumber explain whether a sweated or press joint is the better long-term choice.
Listening equipment hears the leak, and a thermal camera maps the wet area through the drywall. That combination typically keeps the cut small and easy to patch later.
A single leak on newer pipe often makes sense to spot repair through the floor. If the line has leaked before or the pipe is old, rerouting through walls or the attic avoids chasing the next one.
Let faucets on outside walls drip on hard freeze nights and open the sink cabinets so warm air reaches the pipes. Insulate exposed runs and add heat tape where pipes pass through cold crawlspaces, starting with the spots the plumber flags.
We route calls to independent plumbers working all over Memphis, from older neighborhoods with galvanized lines to newer builds plumbed in PEX. Nearby suburbs are covered too, along with zip codes such as 63555.
Older homes near the center of town tend to have galvanized mains and thin copper branch lines, which is where pinhole leaks and corroded threads show up. Newer subdivisions are mostly PEX or CPVC, so blown crimp fittings and cracked elbows top the list there. Wherever you are, tell the dispatcher the age of the house and we match the plumber to the pipe.
Crawlspace freezes, attic lines, and slab leaks in houses of every age.
Leaks that cross into a neighbor's unit, where fast shutoff and documentation both matter.
The same contractor network reaches the suburbs around Memphis.
